Pipe Fittings and Flanges Manufacturers in India | Seamless & Welded Pipe Manufacturers | Flexible Hose Pipe Manufacturers | Email Us on sales@metline.in
₹3,500.00
**Incoloy® is a registered trademark of the Special Metals Corporation group of companies
Incoloy 800,Incoloy 800H , and Incoloy 800HT are nickel-iron-chromium super alloys. When exposed to high-temperature these alloys not only provide excellent resistance to oxidation and carburization but also good strength too. These nickel steel alloys are similar except for the higher level of carbon in Incoloy 800H, and the addition of up to 1.20 percent titanium and aluminum in Incoloy 800HT.
| STANDARD | INCOLOY 800 | INCOLOY 800H | INCOLOY 800HT |
| UNS | N08800 | N08810 | N08811 |
| WERKSTOFF NR. | 1.4876 | 1.4958 / 1.4876 | 1.4959 / 1.4876 |
| EN | X10NiCrAlTi32-20 | X5NiCrAlTi31-20 | X8NiCrAlTi32-21 |
| BS | NA 15 | NA 15(H) | NA 15(HT) |
| OR | XH32T | XH32T | XH32T |
| GOST | ЭИ670 | ЭИ670 | ЭИ670 |
| JIS | NCF 800 | NCF 800H | NCF 800Ht |
| AFNOR | Z8NC32-21 | Z8NC33-21 |
| ELEMENT | INCOLOY 800 | INCOLOY 800H | INCOLOY 800HT |
| NI | 30.0 – 35.0 | 30.0 – 35.0 | 30.0 – 35.0 |
| CR | 19.0 – 23.0 | 19.0 – 23.0 | 19.0 – 23.0 |
| FE | 39.5 min | 39.5 min | 39.5 min |
| MN | 1.5 max | 1.5 max | 1.5 max |
| C | 0.10 max | 0.05 – 0.10 | 0.06 – 0.10 |
| CU | 0.75 max | 0.75 max | 0.75 max |
| SI | 1.0 max | 1.0 max | 1.0 max |
| S | 0.015 max | 0.015 max | 0.015 max |
| AL | 0.15 – 0.60 | 0.15 – 0.60 | 0.15 – 0.60 |
| TI | 0.15 – 0.60 | 0.15 – 0.60 | 0.15 – 0.60 |
| * UNS N08811 : Al + Ti = 0.85 – 1.20 | |||
| MELTING POINT | 2475 – 2525 °F/ 1357 – 1385 °C |
| SPECIFIC HEAT @ 70°F | 0.11 Btu/lb•°F |
| PERMEABILITY @ 70°F ANNEALED | 1.014 (200 Oersted) |
| CURIE TEMPERATURE | -115 °C/ -175 °F |
| ELASTIC MODULUS | 28.50 X 106 psi |
| ELECTRICAL RESISTIVITY @ 70°F | 595 ohm•circ mil/ft |
| ANNEALLING INCOLOY 800 | 983 – 1038 °C / 1800 – 1900 °F |
| ANNEALLING INCOLOY 800H / HT | 1147 – 1177°C / 2100 – 2150 °F |
| QUENCH | Rapid Air / Water |
| Density | 7.94 g/cm3 |
| Melting Point | 1385 °C (2525 °F) |
| Tensile Strength | Psi – 75,000 , MPa – 520 |
| Yield Strength (0.2%Offset) | Psi – 30,000 , MPa – 205 |
| Elongation | 30% |
| Size | Normal Dia : ¼" to 4" 6-100 mm |
|---|---|
| Surface Finish | Blackening, Cadmium Zinc plated, Galvanized, Hot Dip Galvanized, Nickel Plated, Buffing, P.T.F.E. Coated |
| Threads | Metric, BSW, BSF, UNC, UNF, and as per costumers requirement |
| Meaning | A nut is a type of fastener with a threaded hole. Nuts are almost always used opposite a mating bolt to fasten a stack of parts together. The two partners are kept together by a combination of their threads' friction, a slight stretch of the bolt, and compression of the parts. |
| Grades | DIN 6915 CI. 10, Stainless Steel AISI 304 / 316. Heavy hex nuts ASTM A194 Gr.8, 8M |
